DPH-70 voice menu helps you through the configuration process. You can enter the configuration
menu by pressing the key sequence   *123*   and terminate with a hash (#) key when DPH-70 is in idle state.

DPH-70 will ask for password on entering configuration menu. Since the configuration information contains valuable information it is password protected. If you don’t remember your password, you can reset DPH-70 to default password as described in Loading factory defaults. The default password is ‘12345’.

Warning: DPH-70 identifies end of a parameter by ‘#’. Please terminate each parameter entry into DPH-70 by pressing ‘#’ key.



 

DPH-70 configuration menu is shown above. It has five options in the main menu and seven options in the extended menu. Each of them is described below. The configurable parameters are shown in bold letters. DPH-70 plays the current value of each parameter and allows you to edit or skip to next parameter. After entering a parameters value, it plays it back for verification.

After password verification, DPH-70 will play the main menu as below.
“Press

‘1’ to enter ISP parameters,
‘2’ to enter calling card parameters,
‘3’ to enter extended menu,
‘4’ to review configuration parameters,
‘5’ to save & quit

Note:
If power goes off while you are configuring, the phone will work with the previous saved parameters.
If you idle more than 90 seconds, dph-70 will accept the keys entered and go to next state.
If you leave the phone without completing the configuration it will go back to idle state
without saving the parameters.

 


1. ISP Parameters

DPH-70 needs to connect to the Internet to make Internet phone calls. The following information should be configured in DPH-70 to connect to the Internet and make calls. The user will get this information while subscribing to Internet Service Provider (ISP). Please note that DPH-70 will not work without this information.

ISP Phone Number

This is the phone number to which DPH-70 will dial-up to connect to the Internet. The Internet access phone number can be maximum 20 digits. If you enter more digits and try to save, you will hear a prompt “ The parameter you have entered is incorrect, Press ‘1’ to edit, ‘2’ to skip”. Press ‘1’ or ‘2’ appropriately.

DPH-70 normally dials out with DTMF tones. However, if Internet access phone number is configured to start with a ‘?’, then the phone dials out in pulse mode.

DPH-70 has special supports for operation behind an EPABX. In some scenarios, you may have to introduce a delay after dialing external access number or wait for secondary dial tone. A ‘.’ (dot) in phone number will introduce a delay and a ‘_’ (under-score) will look for secondary dial tone. For example, 9*6788341 will introduce a small delay after dialing 9, before dialing other digits.

ISP User Name

The user name used for identifying the user to Internet Service Provider (ISP). It can have a mix of digits, lower and upper case letters, and special characters. The user name can have a maximum of 30 characters. Please refer to Appendix A: Procedure for entering alphanumeric and
special characters to enter special characters.

ISP Password

The password used for verifying the user to Internet Service Provider (ISP). It can have a mix of
digits, lower and lower case letters, and special characters. It can have a maximum of 30 characters. Please refer to Appendix A: Procedure for entering alphanumeric and special characters to enter special characters.

 

2. Calling Card Parameters

The following information is required for DPH-70 to make and receive Internet phone calls. The user will get this information from the VoIP (Internet Telephone) service provider. Please note that
DPH-70 will not work before configuring this information.

Calling Card User ID :-  (Eg. 123 )

This is the Internet phone number or user ID assigned to you. It can have a maximum of 30 characters. This information is required to verify the calling card user identity to the VoIP (Internet Telephone) Service Provider.

Calling Card Password :-  (Eg.  BATCH-165-14881) 

This information is required to verify the calling card user identity to the VoIP (Internet Telephone)
Service Provider. It can have a maximum of 30 characters.

 

VoIP Server Address :-  
(password :- 'abcd'     Our Server address :-  202.79.221.193 )

This is the IP address where VoIP (Internet Telephone) Server is running. It can be a valid IP address like 202.79.221.193. The domain name can have a maximum of 30 characters, including ‘dots’. Default server address is sip.dlink.co.in VoIP server address is of the form xxx.xxx.xxx.xxx where xxx is between 0 and 255. If the entered number is invalid, phone prompts with a message “ The parameter you have entered is incorrect, Press ‘1’ to edit, ‘2’ to skip”.

 

3. Extended Menu

 

4. Review Configuration

This option plays current information for all parameters in main menu as
“ISP Phone number is xxxx,
ISP User name is xxxx,
ISP Password is xxxx,
Calling Card user ID is xxxx,
Calling Card password is xxxx,
VoIP server address is 202.79.221.193”
After playing this message, it prompts with the main menu.

 

5. Save and Exit

This option saves all the information entered in the configuration and exits from configuration
option. You can leave the configuration without saving the information by replacing the handset or
switching the speaker off.

 

 

Extended Menu details :-

1 Configuration Password

Internet access and calling card parameters are valuable information and it can be misused. Thus, DPH-70 has password protection to enter the configuration module. It can have maximum of 30 characters. Default is "12345". The user is advised to change this value. If you forget this password, reset the phone to factory values and configure the phone again.

2 Software server address

This is the IP address of software server from where the latest DPH-70 software can be downloaded. It can be a valid IP address like 198.62.73.101 or a valid domain name like dph70.dlink.co.in. The domain name can have maximum of 30 characters, including ‘dots’. Default server address is dph70.dlink.co.in (or 202.62.83.106).

3 Country Code

Following is a list of countries supported with their respective codes

Table 1 Country Codes
Country Code
Brazil 0
China 1
India 2
Korea 3
Malaysia 4
Mexico 5
South Africa 6
Taiwan 7
USA 8
Others (India) 9

If you enter a value other than the listed, the phone prompts with a message “The parameter you have entered is incorrect, Press ‘1’ to edit, ‘2’ to skip”. Choose appropriately. Based on the country code selection, the various tones and modem software will vary. Default country code is 2 (India). If you change it to some other country than yours, the phone may not be able to make calls and you will hear some error message. So please be sure to select the correct country code.

4 Language Support

DPH-70 plays voice prompts in many languages. Following is the list of languages supported with their respective codes.




If you enter other than the listed value, the phone prompts with a message “The parameter you have entered is incorrect, Press ‘1’ to edit, ‘2’ to skip”. Choose appropriately. If you change the language code, please do a software upgrade as described in Upgrading Software section.

5 VoIP Service Provider

DPH-70 works with many service providers. Following is the list of service providers supported with their respective codes.




If you enter other than the listed value, the phone prompts with a message “The parameter you have entered is incorrect, Press ‘1’ to edit, ‘2’ to skip”. Choose appropriately. If you change the service provider code, please do a software upgrade as described in Upgrading Software section.

6 Software version number

This option plays the current software version in DPH-70. It will change if you download newer version of software from Internet.

7 Review Configuration

This option plays current information for all parameters in extended menu as

“Configuration password is x
Software server address is x
Country Code is x
Language selected is x
VoIP Service provider is X
Current software version is x”
After playing this message, it prompts with the extended menu.

8 Exit to main menu

This option takes you to the main menu. You need to save the information entered in extended menu by selecting ‘Save and Exit’ in main menu.

The section describes how to enter digits, upper and lower case alphabets, and special characters using the DPH-70 keypad shown below.



8.1 Entering Digits

1. Entering Small Letters

Press a digit key twice to enter the first character written on that key.
Press thrice to enter the second character written on that key
Press four times to enter the third character written on that key.
Press five times to enter the fourth character written on that key.
If the key is pressed more than above mentioned times, it accepts the last letter written
on that key.

Examples: To enter a, press key 2 two times.
To enter e, press key 3 three times.
To enter z, press key 9 five times.

NOTE: Press the appropriate key firmly, specified number of times, in quick succession to enter
alphabets.

2. Entering Capital Letters

You need to press a SHIFT button and a digit key, specified number of times, to enter the capital
letters marked on digit keys. SHIFT LED turns on after SHIFT button is pressed and turns off after
the digit key is pressed.

Press a SHIFT button and then the digit key, the following number of times to enter the
capital letters.
o Twice to enter the capital of the first letter written on that key.
o Thrice to enter the capital of the second letter written on that key.
o Four times to enter the capital of the third letter written on that key.
o Five times to enter the capital of the fourth letter written on that key.
If the key is pressed once after SHIFT button is pressed, it accepts the corresponding digit.
If the key is pressed more than above mentioned times after the SHIFT button is pressed, it accepts as a last capital letter written on that key.

Examples: To enter A, press SHIFT followed by key 2 two times.
To enter E, press SHIFT followed by key 3 three times.
To enter Z, press SHIFT followed by key 9 five times.

NOTE: Press the appropriate key firmly, specified number of times, in quick succession to enter alphabets.

3. Entering Special Characters

Press DIAL UP button and then press the corresponding key mentioned in table below to enter special characters. DIAL UP LED turns on after pressing the DIAL UP button and turns off after accepting a special character.



Note: Backspace can be used to delete the unwanted character. It will delete the last entered
character.

Examples: To enter @, press DIAL UP followed by key 1.
To enter ., press DIAL UP followed by key 2.
To delete the last character, press DIAL UP followed by key 0. 

DPH-70 can play the following error messages at different error conditions. These messages aid
in troubleshooting any error conditions.

All outgoing calls are PSTN calls. It does not dial in Internet mode.
To make a call in Internet mode, you have to press DIAL-UP button first. Please refer to the user manual for more details. If you don’t press DIAL-UP, DPH-70 will dial out in PSTN mode.

“Please configure the phone and try again”
This message is played if you try to use DPH-70 without configuring important parameters. You need to configure the Internet Service Provider (ISP) access parameters and VoIP (Internet Telephone) calling card parameters to use the phone.

“Please check the phone line and try again”
This message is played if DPH-70 is not connected to the phone line properly. Please check the phone line connection and try again. Test the phone line with a normal phone if it persists. If DPH-70 is behind EPBX you may have to program DPH-70 to look for secondary dial tone or introduce a delay. Please refer to configuration section for more information.

“Password entered is incorrect. Try again”
If invalid password is entered to access configuration state, this message is played.

“The ISP line is busy, please call after some time”
This message is played when the Internet access line is busy. This may happen during peak hours.

“The ISP server is not responding”
It is played when the Internet access modem is not responding properly. If this happens please check the Internet access phone number and country code in configuration menu. If you call Internet access phone number from a phone you will hear modem noise.

“ISP connection could not be established, try later”
It is played when Internet access server is down. Please contact the ISP customer service or try again after some time.

“Please check your ISP parameters and try again”
This message is played when the configured ISP user name and password is incorrect. Please verify the ISP user name and password.

“Bad phone line, Please contact customer support”
It indicates that your phone line may not connect to the Internet at sufficient speed to establish Internet phone calls. Please try another phone line or contact customer support.

“Please check your calling card parameters and try again”
This message is played when the configured calling card information is incorrect. Please verify the calling card parameters. This may also be due to VoIP server not responding or no balance in
your calling card account or wrong VoIP server IP address.

“The number you have dialed is not locatable, please check the number”
This message is played when the called phone number does not exist or not ready to receive calls.

“The number you have called is busy, please call after some time”
This message is played when the called phone is busy.

“Incorrect value. Press ‘1’ to edit, ‘2’ to skip”
This message is played when invalid information is entered as part of configuration.

Fast error tone for a short period while disconnection phone
This error tone is played while the modem disconnects from the Internet. This process takes a short time and the phone is inaccessible during this period.